![]() IT IS RECOMMENDED THAT YOU ARCHIVE THE DEVICE ON YOUR EASYLOG™CLOUD DEVICES PAGE BEFORE UNDERTAKING A FACTORY RESET. The device will no longer be connected to any network or EasyLog™ Cloud account. Doing this will return the device to the factory state, deleting all settings and clearing any remaining data. If necessary, a full factory reset can also be performed by holding the button for 20 seconds until FArS appears on screen. It will continue to be connected to the account it was set-up with and will simply start a new recording session. The device will retain all settings but will lose any data that had not been transferred to the EasyLog™ Cloud. Release the button when RST appears on screen. WIFI: The device can be reset by holding the button for 10 seconds. Clicking this will open up a pop up with information on the pending firmware update and give you the option to install an over the air firmware update.Īlternatively multiple devices can be updated via the burger menu in the top right of the devices panel, by selecting any of your devices, then opening the burger menu, selecting the “Update Firmware” option. If you have an update pending you will see a yellow warning triangle will appear in the device cell. MOTE: The MOTE can be updated via the device page on either the device cell or from the Burger menu located at the top right of the devices page. Any existing data for this device on the EasyLog™ Cloud will be archived for safe-keeping. Depending on the previous firmware version, your device may be in a factory-reset condition following a firmware update, and will need to be connected to the EasyLog™ Cloud using the EasyLog™ WiFi Software. To benefit from the latest improvements we recommend using the latest firmware releases for your devices. You’ll need to connect the device to the PC using the USB cable provided then follow the on-screen instructions to download and update the latest firmware versions. You can update the firmware in a device by running the Firmware Updater software (installed on your PC with the WiFi Sensor Software). WIFI: The WiFi devices contain program code that runs internally, often referred to as firmware. Only the types listed are supported.ĩ) Make sure that the SSID name does not contain spaces. ![]() Make sure that the configured DHCP IP address range allows the addition of new devices if not, then extend the range.Ĩ) If your wireless network uses WPA Enterprise, make sure that the correct authentication type is selected from the drop-down box. Normally, the DHCP service runs in either your router or on a network server. This allows the device to be allocated an IP Address. Alternatively, search the web for resources to help convert your password to a HEX key.ħ) Check that DHCP service is running. You can find the HEX key in the internal settings of your access point or router. If it is switched on, only known devices will be able to connect to your router.ģ) Check that your network has an internet connection.Ĥ) Check that the device is in range of the router.ĥ) Check to see if the router has the latest firmware.Ħ) If the access point or router has WEP Encryption ensure that the HEX key is being entered rather than the password. With a hybrid solution, you get the best of both worlds cloud administration and management, local speeds and you achieve a minimum of bandwidth usage.WIFI/MOTE: You can try any or all of these steps to help with this problemġ) Check that the password being entered is correct.Ģ) Ensure MAC filtering is not switched on in the access point or router. It can also be a child server with local administrator options and again as a software server with PXE, this is also connected via https to the cloud server. a local distribution point such as software server and PXE connected to the cloud server via https. With Eas圜loud you do not have to maintain the EasyInstall server – we take care of everything and update the server solution with Microsoft and EasyInstall and updates in established service windows so that your business is not disturbed unnecessarily.Īll our cloud servers are physically located in Denmark.Įas圜loud supports hybrid solutions, e.g. Eas圜loud is a so-called Software-as-a-Service (SaaS) solution.The benefits of Eas圜loud includes flexibility, fixed costs, innovation, availability, scaling and security. ![]() ![]() With Eas圜loud you get the same – as an ‘on-premise’ solution with all the benefits of a cloud world. Is your company 100% Cloud-based or do you want to save time of maintaining, configuring and updating your EasyInstall server? ![]()
0 Comments
Leave a Reply. |